jared payne
Members-
Content count
107 -
Joined
-
Last visited
Everything posted by jared payne
-
jared payne added a post in a topic Testing Fabric
Hi Fred thanks for the reply. I really enjoy your videos. I think I may try the Oratex product, if anything I will shave some weight. Thank you Thank you. I hope they can send me a color chart. cheers
-
0
-
-
jared payne added a topic in Avidfoxflyers General Hangar
Fusalage strectchI have been looking and asking for imfo and pictures about this proses,Would like to do this to my Mk4 but do not know where to cut . Any help would be great thanks
- 0 replies
- 378 views
-
jared payne added a post in a topic My mk4
With the right tool the clutch came off in about 30 seconds. I am waiting on my c box from Teal with adapter hopefully this week. Working on cowling mockup and engine mounts to keep me busy. Ordered the radiator yesterday, and will order prop this week. Need to decide on the tires I want, the biggest for the buck 6in rim.
-
1
-
-
jared payne added a post in a topic My mk4
More progress
-
2
-
-
jared payne added a post in a topic Testing Fabric
If you don't mind me asking what did it cost to cover you c model in Oratex?
-
0
-
-
jared payne added a post in a topic Big wheels and upgraded gear wanted for Avid 4
I have thought of going back to the float fitting center for just that reason,but trying to shave weight. Maybe on the fourth set. I have thought of offering them up to someone willing to test, because I am so far out.
-
0
-
-
jared payne added a post in a topic Big wheels and upgraded gear wanted for Avid 4
I under stand what you are saying is when landing and braking the gear could go aft? To do what Beringer does I would have to omit the rear leg , or it would bind. Again I am amazed how much lateral force the groove gear can take with a little clamp holding it to the fuse, think of that load.
-
0
-
-
jared payne added a post in a topic Tundra tire
That looks awesome, but not in my budget
-
0
-
-
jared payne added a post in a topic Big wheels and upgraded gear wanted for Avid 4
Needs testing.
-
1
-
-
jared payne added a post in a topic Engine thrust angle
exactly. in length but not height . Received motor mount material and exhaust material today. am going to catch you Was thinking of naming my wife's plane shock and awe. Awe for when it breaks.
-
1
-
-
jared payne added a post in a topic Engine thrust angle
I would lengthen the fuse if I could find out where to cut. It looks like a lot of work with the rudder cables replace elevator trim cable replace and realigning the elevator pushrod tube.
-
0
-
-
jared payne added a post in a topic Engine thrust angle
I would move the back of the motor and leave the prop centered in the cowling cut out. Do the avids fly tail down our level? Can somebody check the prop flange to fire wall with either 582 912 or soob. This is a measurement I should have taken before selling my 582. To night I sat the motor in the rough location, it looks like if I cut two tubes out of the way and reroute I could move the motor back 3.5 inches is this worth 5 hrs work? I know my time is not worth shit but I do want to be done and flying someday, you guys are great.
-
0
-
-
jared payne added a post in a topic Big wheels and upgraded gear wanted for Avid 4
The shocks cost $249 each and weigh 7.8 pounds the hole gear weigh about 45lbs.I plane on building litter ones after testing to see what I can shave and get away with
-
0
-
-
jared payne added a topic in Rotax and other engines
Engine thrust angleI am putting in a Yamaha into my Mk4. I understand you want 3-4 degrees to port , but what about up or down? Where is the water line on a mk4? Fire wall is guite a bit diff than bottom of fuse
- 17 replies
- 1,490 views
-
jared payne added a topic in Avidfoxflyers General Hangar
-
jared payne added a post in a topic My mk4
Bottom of fuse is a lot different than fire wall. When I level below seat fuse the fire wall is about 1 in out of plumb, Maybe go with the average?
-
0
-
-
jared payne added a post in a topic Big wheels and upgraded gear wanted for Avid 4
Build your own.
-
2
-
-
jared payne added a post in a topic My mk4
Working on motor mount for Yamaha, I think Teal said level prop flange with fire wall, what should I use for the water line? Fire wall and door sill / elevator are different. I am going with 3 degree to the port.
-
0
-
-
jared payne added a post in a topic My mk4
Where would you make the cuts lots of angles
-
0
-
-
jared payne added a post in a topic My mk4
Just a update
-
3
-
-
jared payne added a post in a topic YAMAHA RX-1 (140 HP) install in Kitfox 5
How did you get the primary drive off of the rx1 ? I tried the water method and a 4in 3 jaw puller no luck , what is the secrete? I was thinking of renting a bigger puller.
-
0
-
-
jared payne added a post in a topic Need help
I am going to catch up to you
-
0
-
-
jared payne added a post in a topic Yamaha RX1 Engines
Copros air box ? did Steve make that or is that a store? Looks nice and lite.
-
0
-
-
jared payne added a topic in For Sale and wanted, you got it, I want it
MinimaxAnyboby interested in a Minimax 1030r very nice with trailer, $4500. Can be seen on craigslist Bellingham wa. 5% finders fee if sells.
- 0 replies
- 450 views
-
jared payne added a post in a topic My mk4
Interesting videos I plane on going with some kind of muffler on my wife's plane
-
0
-