Justin

Members
  • Content count

    27
  • Joined

  • Last visited


Everything posted by Justin

  1. Justin added a post in a topic Please Input on rotax ricks rebuilds   

    Well I ended up going with rotax Rick and am very pleased with his rebuilds. So far the motor is doing good and performing amazing he is very very helpful with any questions or concerns he will help you with anything he can so unfortunately I can't help you with bill Larson but I have heard good things about him as well if you have any specific question feel free to ask 
    • 0
  2. Justin added a post in a topic Rotax 582 front cylinder EGT HIGH   

    Thanks for all the info guys I have lots to try now I determined that the probes are reading acuratly this morning so I know now that's it's a definite carb or engine related problem I will give these things a try and see what I come up with this is some of the temps at 5800 with front carb on factory clip spot and back carb 2nd clip from top 



    • 0
  3. Justin added a post in a topic Rotax 582 front cylinder EGT HIGH   

    Well I used rotax Rick and I have asked him a few questions before I ruled out what I know now he was saying it could be the jetting in the carb he said I may need to run a bigger main jet or change the needle but I feel that would do anything but mask a bigger problem I am no two stroke genius that's were I leave it up to all the amazing knowledgeable people on this site 
    • 1
  4. Justin added a post in a topic Rotax 582 front cylinder EGT HIGH   

     OK so I swap the carbs and the front cylinder still runs hotter I also swapped the EGT probe's front to rear rear to front  I also tried two analog gauges plus matching it with my EIS and everything seems to match out that the front cylinder still runs hotter all the jetting in the carburetors match and all the needle clips are the same I am at an absolute loss wondering what it could be checked the carbs  Sockets and couldn't find any air leaks. 
    Is it possible a base gasket sucking air on the front cylinder thanks 
    • 0
  5. Justin added a post in a topic Rotax 582 front cylinder EGT HIGH   

    Ya I am going to swap carbs around today and try that and also inspect the carb sockets. I did switch the probes and front still runs hotter hopefully I'll get some answers by switching the carbs thanks 
    • 0
  6. Justin added a topic in Two Strokes   

    Rotax 582 front cylinder EGT HIGH
    Can anybody please help me figure out why my completely overhauled rotax 582 blue head is running high EGTs on the front pto side cylinder back cylinder runs around 1000 to 1050 at 4500 rpm and the front wants to climb right up to 1100 and keeps on going if I let it which I have not it's got all rebuilt carbs including all jets needle clip and ECT.. any advice would be greatly appreciated I have already determined it's not gauges it is I tried analog after thinking it could be my EIS please help new motor new prop new glass panel and still on the ground 
    • 19 replies
    • 4,375 views
  7. Justin added a post in a topic HELP can anyone tell me what this means   

    Okay great I was In the process of putting my c box back on and ran into the fact I didn't see the shim they were so called explaining I also wandered why it says as required I guess I need to figure out how that mesurment is taken before I go any further thanks for the advice 
    • 0
  8. Justin added a topic in Two Strokes   

    HELP can anyone tell me what this means
    what does it mean on a rotax C box 3.1 put the # 16 shim on the pinion shaft as required 
    • 8 replies
    • 1,170 views
  9. Justin added a topic in For Sale and wanted, you got it, I want it   

    Excellent shape RK 400 clutch for c box
    Excellent shape RK 400 clutch with new clutch shoe pack and spring 450.00 Obo call Justin at 5419820006 or text thanks guys 
    • 0 replies
    • 839 views
  10. Justin added a post in a topic Looking for a 582 Cylinder   

    Joey there is a pretty good deal on eBay for two cylinders Pistons and the head for 695.00 free shipping it is a 582 grey head but cross hatching and everything looked really good 
    • 0
  11. Justin added a post in a topic Rotax 582 top end rebuild   

    Okay thanks I'm still kinda on the fence about what I should do exactly really just looking for advice 
    • 0
  12. Justin added a post in a topic Rotax 582 top end rebuild   

    Jim were is this shop located that did the work for you 
     
    • 0
  13. Justin added a post in a topic Rotax 582 top end rebuild   

    Well back piston is scored my eclip on needle In back carb vibrated and cut off one of he adjustment rings and leaned out back cylinder caught it in time no seizure but burnt the piston and scratched up the cylinder wall a little so was going to put new pistons and rings along with inspecting crank 
    • 0
  14. Justin added a topic in Two Strokes   

    Rotax 582 top end rebuild
    Hey guys just wanting to get some input on top end kits for rotax 582 any input would be greatly appreciated thanks like to hear what you know 
    • 8 replies
    • 2,174 views
  15. Justin added a post in a topic Please Input on rotax ricks rebuilds   

    Have any of you guys running 582 heard of the aeroteks rebuild kit top end 
    • 0
  16. Justin added a post in a topic Please Input on rotax ricks rebuilds   

    Thanks for all the input I think I have decided to go with bill at Oregon aviation spoke with him on the phone today and really appreciated all his knowledge and help on what would be best to do I'll let you guys know how it goes once I get it done 
    • 1
  17. Justin added a post in a topic Please Input on rotax ricks rebuilds   

    Oregon coast figured I could find some good information I really would like to rebuild on my own due to cost 
     
    • 0
  18. Justin added a topic in Rotax and other engines   

    Please Input on rotax ricks rebuilds
    In the process of finding someone to rebuild my 582 just want any advice you guys can throw at me wether it's doing my self or someone else, oem pistons or if some of you guys run good aftermarket any advice is amazing thanks 
    • 19 replies
    • 5,041 views
  19. Justin added a post in a topic bing 54 carb vent lines   

    okay so I am having the same issue rough idle fuel out vent lines and I just installed a 72 inch ivo not sure if they are the medium blades I was told they were called ultralight plus blades are these also considered mediums thanks justin 
    • 0
  20. Justin added a topic in Kitfox IV   

    Kitfox 4 fuel tank kreem peeling
    I have a kitfox 4 and upon inspection I realized both fuel tanks the kreem is peeling away showing bare fiberglass my question is what options do I have replace them with new or are there other oprions out there thanks 
     
    • 8 replies
    • 2,537 views
  21. Justin added a post in a topic Fuel line air bubbles   

    Ya my filter is after the gascolator before mechanical Pump once I resolved the issue I had no problems flew for a hour without any symptoms 
    • 0
  22. Justin added a post in a topic Joey's flying channel   

    Not 27s but sure better then what I had 

    • 2
  23. Justin added a post in a topic Fuel line air bubbles   

    There is a filter In line before gascolator 
    • 0
  24. Justin added a topic in Kitfox IV   

    Fuel line air bubbles
    Just a quick question to see if anyone has ran into this problem I trailer my Kitfox to airport for flights tanks were fairly low got to airport did my pre flight and noticed had very little amount of fuel coming from gascolator drain when checked let it run then stopped flowing so first thing I did was pull of gascolator to find it super clean next I pulled the line off the selector valve to find little fuel coming from header tank so I blew back into the line heard bubbles in tank then came fuel I am kinda at lose whether it was a air lock or junk in line filter is clean and no junk in gascolator and advice helps thanks 
     
    • 5 replies
    • 1,198 views
  25. Justin added a post in a topic 3 blade wood Prop hub and spinner for rotax 582 great shape   

    So sorry dan phone was broke and didn't have net any other way yes it is a great shape ground adjustable 3 blade GSC and the diameter is 68 I believe have to double check it's on a 582 upright with b box in kitfox 4 
    • 0